UsbComMode ayarn bata 2 olmak zere 1 ve 0 olarak da denedim fakat sonu alamadm.

Delta Hmi Dop B Usb Driver Gerekiyor Olabilir

Sorunu nasl zebilirim DOP-B Serisine balant iin herhangi bir driver gerekiyor olabilir mi Not: Pc Windows 10 yi almalar.

Yok ise farkl port, farkl USB kablo ve hatta farkl PC ile ayn testi gerekletirin.

Deien olmaz ise HMI usp portunda fiziksel sorundan bahsediyor olacaz.

USB kablosu ve PC usb portunun alrln dorulamak iin Commode ayarn 1 yapn ve ardndan usb kablosunu karp taktnz zaman Bilgisayarm ierisindeki srclerde DELTA isimli bir diskgryor olmalsnz.

Program tamamen kaldrp tekrar ykleyince sorun zld.

Usb zerinden program yklemek istiyorum yol gsterirmisiniz Teekkr ederim.

Elinizde var ise Windows XP ykl bir PC zerinden bir defa yazlm gncellemesi yaparak USB com modunu ayarlayabilirsiniz.

Com1 portundan rs232 dntrcyle 2-3-5 terminallerinden balanmaya alyorum.

All drivers available for download have been scanned by antivirus program. 2: Driver Auto Navigator; Automatic detection and download sound driver, printer, scanner driver, modem driver, motherboard drivers, a Bluetooth controller, Ethernet.

I has always (as far as I remember) been fine programming it here on this desktop PC (Win 8) but now Ive had to move the PLC to a test room Ive had to try and program it over USB using another computer (a Lenovo Yoga notebooky-laptop type thing running Win 8.1).

Delta Hmi Dop B Usb Install Properly The

Ive installed the UniLogic software as before, even uninstalling and reinstalling again, making sure I installed the second time using Run as Administrator on the installer, in case that didnt allow something to install properly the first time.

With both the first time around and second time around install, the programs all load up fine and everything else looks the same as it ever did on the version I have on this desktop PC (the latest version, Ver.

Rev19), but I cant get my laptop to connect to the PLC.

I have tried things Ive found on this forum, like: powering off the PLC and trying again; powering off the PLC, unplugging the USB cable, closing UniLogic, killing the Unitronics Notifier (via the Task Manager), restarting UniLogic, powering on the PLC, and after the PLC has booted, plugging the USB cable back in.

I have tried all kinds of combinations of these things, multiple times, and still ahve had no response from UniLogic when trying to connect to the PLC.

Sometimes (though rarely, compared to my desktop) it comes up with the message about connection problems (Connect PC to PLC.

Not discovered. Etc.) in the PC-PLC Communication window, but when I press the Refresh buttonhyperlinklink, where it usually says (on my desktop) Searching for hardware.

Download Amd Sata Controller Driver Windows Xp., for maybe 5-10 seconds and then finds the PLC, on my laptop it immediately returns to the Connect PC to PLC.

There are 2 USB ports on the laptop; one is USB 3 and one is USB 2.

I have tried all of these things in both ports, several times.

Please help. I dont wan tot have to move this desktop computer to the PLC, as theres no space to use it in the test room Hello, Please try following these exact steps to initialize communications over USB in UniLogic.

Please try to power OFF the PLC Close UniLogic Unplug the USB cable Make sure the PLC is grounded (power supply for notebook) Power ON the PLC When you see the initializing green spin logo, plug the USB cable After the PLC finished to Boot up Open UniLogic and try to download the project.

If needed, In the discovery window click on the Refresh link few times If it didnt helped please try to install the driver manually, the path is C: ProgramData Unitronics UniLogic Drivers Below you can download the content from this path.

Please ensure you set your Windows operating system to support unsigned USB drivers, as this is a requirement for Windows 88.1.

Let us know if this helps.

If the problem still persists, please contact supportunitronics.com for further troubleshooting.

Please open the device manager (while the PLC is disconnected from the computer).

Expand both Network Adapters and Ports (COM LPT) Now, connect the PLC.

Was the PLC added to the Network Adapters as Unitronics Unistream USB EthernetRNDIS Gadget, or was a Serial Com Port added to the Ports Windows 10 might recognize the PLC as a serial port, which in this case, the driver should be browsed specifically, while the signed drivers enforcement is turned off.

Ive been told USB on Unistream is a virtualized ethernet adaptor.

I found that AVAST firewall was blocking USB connectivity but not ethernet when using my laptop on UniStream15.6.

Turning third party firewall off allowed USB connection to work.

My discovery may not have any relevance to the issues being encountered o this thread but is an easy thing to try.

Ive also seen AVG FREE interfere with serial communucations to CAC card readers.

Spent hours fidling with drivers to only find its an AV problem.

Use the links on this page to download the latest version of PLC USB Device drivers.

All drivers available for download have been scanned by antivirus program.